When was SKILL++ first released?
I know it was after June, 1993.I know it was before SKILL 04.30 (IC441), which was 1997.
View ArticleCan't set popup
Hi,I can't set popup unless app mode is "none".Here is the code, I am using SPB16.6 with hotfix030.Thanks a lot. (defun cbc_select ()let(() cbc_select_popup = axlUIPopupDefine( nil (list (list...
View ArticleFinding Layer Box In a Instance
Hi,I have placed a instance in my cell view(layout). Is there any functions to get the bBox of a particular layer purpose pair, with out flattening the instance.
View ArticleMethod to Add table as a property to the view
Hi I have used the function dbCreateProp and i could add strings as properties to the views.By using for loop,i have tried to add the individual key value pairs as properties to the view.I am looking...
View ArticleSchematic Symbol Libraries
Sorry guys, I'm pretty new here. I'm starting a small project, but I couldn't find any schematic symbol that I need, not even a 100 pins connector. I thought OrCAD comes with some libraries, but what...
View ArticleSweeping Vth vs L
Hi all,I am Arjun, Graduate student pursuing IC Design. I am trying to sweep the Vth of transistor with respect to its length. I saved a file with .scs extension and with the content save M0:all. I...
View ArticleAsk for help: how to do the ac stability simulation for fully-differential...
Hi, there,I am designing a pipelined ADC, and it's my first time to design a fully differential Op-Amp with CMFB & switching-capacitor, it's a little bit difficult for me. In the pipelined stage,...
View ArticleEXPORT IN EXCEL
Hi All,I am trying to export the BOM from the layout in EXCEL format. Any one please let me know the axl command for exporting excel format. Thanks,Karthik.
View ArticleImport Stream (GDSII) from Encounter: Routing is dropped. (XSTRM-58)
Hi,I am using IC614, and trying to import the .gds generated in Encounter into virtuoso layout. The layer mapping file (streamout.map) from Encounter is also loaded. After the stream translating, a...
View ArticleError while running simulation
Hello everyone,I am new to using cadence community forums and I dont know where I can post my following question. While trying to simulate, I keep getting the errors "parameter `n_spec': Unknown...
View ArticleDesign of low pwer RF Receiver for 433Mhz
Hi,I am trying to design a low pwer RF receiver for 433mHz using the Rf receiver IC PT4317-X from princeton technologies. I am using the values for the components as mentioned in the datasheet. I have...
View Articleallegro 3d viewer
I am a begginer at PCB designer 16.6.I tried to set a solid view for one of the layers (let's say TOP Layer) at the 3d viewer, but all I see is the FRAME of the layers.How can I setup this so I can see...
View ArticleipcBeginProcess...
Hi Andrew,I have written a code to open an excel thruogh perl.I am using cid=ipcBeginProcess("perl filename.pl").The perl file is as below ----------------------------------------...
View ArticleReattach technology library without running updater
In ICADV12-ISR7 I have a design library which I want to reattach to a different technology library, but I don't want any of the technology updater code to run to edit my layouts in any way (e.g. to...
View ArticleDrill hole size minimizing in NCdrill Parameter
For my board file, i had placed the NC drill legend below the board. After that in case i want to minimize or maximize the drill sizes in the drill parameter is not get edited.In case of layout, the...
View ArticleIs there any community for sigrity?
Hi.. Is there any community for the sigrity SI & PI analysis??????
View ArticleClik here to view.
how to browse JEDEC type in concept HDL in allegro 16.5
Hi, Any one can help me for how to browse JEDEC type in concept HDL? and I have alredy assigned library path( pad path and psm path) in PCB editor.I am using allegro 16.5 verton tool
View ArticleCreate Via in cadence
Hi All, We have different via spacing after 3x3 array . But its not changing automatically in Create Via Form. Can you please guid me for where to look for it. "In tech.tf "standard via definition...
View Articlehow to remove/release virtuoso license within tool
Hi, I want to release the virtuoso layout license within virtuoso tool.there is any command for this, which i can give in a script to release the license after my work is completed. Thanks
View ArticleNo thru-hole pin region in Cadence
Hi all,I am wondering if its feasible to create a region/area to avoid thru-hole pin in Allegro 16.6 ? Thanks,TDP.
View Article